Watlow EZ-ZONE ST User Manual download pdf (Page 32)

Watlow EZ-ZONE

®

ST • 30 • Chapter 3 Operations Page

Chapter 3: Operations Pages

To go to the Operations Page from the Home Page,

press both the Up ¿ and Down ¯ keys for three sec-

onds. [``Ai] will appear in the upper display and

[oPEr] will appear in the lower display.

• Press the Up ¿ or Down ¯ key to view available

menus. On the following pages top level menus

are identified with a yellow background color.

• Press the Advance Key

‰

to enter the menu of

choice.

• If a submenu exists (more than one instance),

press the Up ¿ or Down ¯ key to select and then

press the Advance Key

‰

to enter.

• Press the Up ¿ or Down ¯ key to move through

available menu prompts.

• Press the Infinity Key ˆ to move backwards

through the levels: parameter to submenu; sub-

menu to menu; menu to Home Page.

• Press and hold the Infinity Key ˆ for two seconds

to return to the Home Page.

Control Module Operation Page Parameters

3

[``Ai]

[oPEr] Analog Input Menu

 [```1]

 [``Ai] Analog Input 1

[`Ain] Process Value

[`i;Er] Error Status

 [`i;Ca] Calibration Offset

[`dio]

[oPEr] Digital Input/Output Menu

 [```1]

 [`dio] Digital Input/Output 1

  [`do;S] Output State

  [`di;S] Event State

[LiM]

[oPEr]Limit Menu

 [```1]

 [LiM] Limit 1

  [`LL;S] Low Set Point

  [`Lh;S] High Set Point

[Mon]

[oPEr] Monitor Menu

 [```1]

 [Mon] Monitor 1

  [C;MA] Control Mode Active

  [`h;Pr] Heat Power

  [`C;Pr] Cool Power

  [`C;SP] Closed Loop Working Set

Point

  [`Pu;A]Process Value Active

[Loop]

[oPEr] Loop Menu

[```1]

 [Loop] Loop 1

  [`C;M] Control Mode

[A;tSP] Autotune Set Point

[`AUt] Autotune Request

[`C;SP] Closed Loop Set Point

  [`id;S] Idle Set Point

  [`h;Pb] Heat Proportional Band

  [`h;hy] Heat Hysteresis

  [`C;Pb] Cool Proportional Band

  [`C;hy] Cool Hysteresis

  [``ti] Time Integral

  [``td] Time Derivative

  [``db] Dead Band

  [`o;SP] Open Loop Set Point

[ALM]

[oPEr] Alarm Menu

 [```1]

 [ALM] Alarm 1

  [`A;Lo] Low Set Point

  [`A;hi] High Set Point

[CUrr]

[oPEr] Current Menu

 [```1]

 [CUrr] Current 1

  [`C;hi] High Set Point

  [`C;Lo] Low Set Point

  [`CU;r] Read

  [`C;Er] Error

  [`h;Er] Heater Error

[P;StA]

[oPEr] Profile Status Menu  

 [```1]

 [P;StA] Profile Status 1

  [P;Str] Profile Start

  [PACr] Action Request

  [`StP] Active Step

  [S;tyP] Active Step Type

  [t;SP1] Target Set Point Loop 1

  [P;SP1] Produced Set Point 1

  [hour] Hours Remaining

[min] Minutes Remaining

[`sec] Seconds Remaining

  [Ent1] Active Event Output 1

  [Ent2] Active Event Output 2

  [``JC] Jump Count Remaining

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 96 97

Comments to this Manuals

No comments