Watlow Series 93 User Manual download pdf (Page 23)

Watlow Series 93 Setup ■ 4.5

Setup

Parameter Value Range Factory Default Appears If:

[`LOC] 0 to 4 0

[``In] [```J], [```H], [```t], [```n], [```S], [```J] DIP switch selectable.

[`rtd], [`r†d], [`0-5], [`420]

[`dEC] 0, 0.0, 0.00 0 [``In] is set to [`0-5] or [`420]

[`C_F] [```C] or [```F] Dependent on [`dFL] [``In] is set to [```J], [```H],

[```t],[```n],[```S], [`rtd], or

[`r†d]

[``rL] [``rL] to [``rh] Input dependent

[``rh] ``rh] to [``rL] Input dependent

[`Ot1] [``ht] or [``CL] [``ht]

[`HSC] 1 to 55, 0.1 to 5.5, 0.01 to 0.55°C 2, 0.2, 0.02°C

1 to 99, 0.1 to 9.9, 0.01 to 0.99°F 3, 0.3, 0.03°F

[`Ot2] [`Con] Control [`Con]

[`PrA] Process alarm

[``Pr] Process with no alarm message

[`dEA] Deviation alarm

[``dE] Deviation with no alarm message

[``no] None

[`HSA] 1 to 5555, 0.1 to 555.5, 0.01 to 55.55°C 2, 0.2, 0.02°C [`Ot2] is not set to [`Con] or [``no]

1 to 9999, 0.1 to 999.9, 0.01 to 99.99°F 3, 0.3, 0.03°F

[`LAt] [`LAt] or [`nLA] [`nLA] [`Ot2] is not set to [`Con] or [``no]

[`SIL] [``On] or [`OFF] [`OFF] [`Ot2] is set to [`dEA] or [``dE]

[`rtd] [`JIS] or [`din] [`din] [``In] is set to [`rtd] or [`r†d]

[`rP`] [`Str] Ramping on power up [`OFF]

[``On] Ramping to set point at all times

[`OFF] None

[`rt`] 0 to 9999 100°/hr [``rP] is not set to [`OFF]

[`P`L] 0 to 100 100 [`Ot1] or [`Ot2] is set to [``ht]

[`dsP] [`nor] normal [`nor]

[`SEt] Set Point (lower only)

[`Pro] Process (upper only)

Input Type Sensor Range Low Sensor Range High

[```J] 0°C/32°F 750°C/1382°F

[```H] -200°C/-328°F 1250°C/2282°F

[```t] -200°C/-328°F 350°C/662°F

[```n] 0°C/32°F 1250°C/2282°F

[```S] 0°C/32°F 1450°C/2642°F

[`rtd] (1°) -200°C/-328°F 700°C/1292°F

[`r†d] (0.1°) -128.8°C/-199.9°F 537.7°C/999.9°F

[`420] 4mA/-999 units 20mA/9999 units

[`0-5] 0VÎ (dc)/-999 units 5VÎ (dc)/9999 units

Table 4.5a -

Input Ranges.

{`dSP}

Table 4.5b -

Setup Menu Prompts and

Descriptions.

Setup Menu

Power Limiting: The power limiting function in % power for heat only. Power

Limiting will function if [`pb1] is not set to [```0].

Range: Dependent on output type. 0 to 100 Default: 100

Display: Selects which displays are active or viewable. Five seconds after select-

ed, the appropriate display goes blank. Press ‰Advance, ¿Up-arrow or ¯Down-

arrow to override this feature and cause the current value to be displayed for 5

seconds.

Range: [`nor] Normal displays Default: [`nor]

[`SEt] Set Point - lower display only

[`Pro] Process - upper display only

NOTE:

Document your Setup

Menu parameters below.

Do not mark any values

here; make photocopies

instead.

[`P`L]

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 51 52

Comments to this Manuals

No comments

Watlow Series 93 User Manual Page 23

Comments to this Manuals

Related products and manuals for Sensors Watlow Series 93