Watlow Series F4S/D User Manual Page 19
- Page / 152
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Watlow Series F4S/D Operations ■ 3.3
π The Profile Key:
• initiates the ramping profile mode;
• initiates the Hold-profile state;
• initiates the Resume-profile command;
• initiates the Terminate-profile command.
The Profile Key functions only from the Main
Page. It will not function from any of the other
pages — Operations, Profile, Setup or Factory.
To Resume a Profile on Hold
1. Press the Profile Key π while a profile is
holding. The Resume Profile Menu appears.
2. Choose to Continue Holding, Resume or
Terminate the profile.
If you do not make a choice, the profile continues
holding and the Profile Indicator Light stays off.
✔
NOTE:
When a profile is resumed during a Ramp step, the con-
troller uses the Static Set Point from the Main Page to
calculate the rate of change needed to get to the set point
at the end of the step. When a profile is resumed in a
soak step, the new set point value will be used as the soak
value for the time remaining in the step.
Resume Profile:_____
>Continue Holding
Resume
Terminate
To Terminate a Running/Holding Profile
1. Press the Profile Key π while a profile is
running. The Profile Action Menu appears.
2. Choose to Continue, Hold or Terminate the
profile. (Default is to Continue.) If you choose to
terminate, the profile ends with all outputs off.
The set point on the Main Page reads off.
If you do not make a choice when the Profile Action
Menu appears, the profile continues as it was —
running or holding.
✔
NOTE:
The Profile Status message takes precedence over all oth-
er information except errors, alarm messages and input
status. Errors and alarm messages always take prece-
dence over Profile Status.
Hold Profile:_______
Don’t Hold
Hold
>Terminate
To Hold a Running Profile
1. Press the Profile Key π while running a pro-
file. The Profile Action Menu appears.
2. Choose to Don’t Hold, Hold or Terminate
the profile. (Default is to Don’t Hold.) If you
choose to hold the profile, the Main Page reap-
pears, and the Profile Status message reads
“Profile X holding.” The Profile Indicator Light is
off.
If you do not make a choice when the Profile Action
Menu appears, the profile continues running and
the profile indicator light stays on.
✔
NOTE:
While profiles are on hold, the step set point value can be
adjusted using the Static Set Point parameter on the
Main Page.
Hold Profile:_______
Don’t Hold
>Hold
Terminate
- User’s Manual 1
- Series F4S/D 1
- About Watlow Winona 2
- About This Manual 2
- Your Comments 2
- Technical Assistance 4
- Warranty 4
- Chapter One: Introduction 5
- 5. Run the Profile 6
- 3. Customize and Name 7
- 4. Program the Profile 7
- 2. Set up the F4 7
- Setup Steps 8
- Navigation 9
- Displays and Indicator Lights 10
- Press < to scroll 11
- > Move Up/Increase 12
- Guided Setup 13
- . to enter 14
- . to move to the 14
- < to go 14
- > and < 15
- Main Page 16
- Chapter Three: Operations 17
- Profile Control π 18
- To Resume a Profile on Hold 19
- To Hold a Running Profile 19
- Alarm Set Points 20
- Auto-tune PID 20
- Edit PID 20
- Multiple PID Sets 21
- Cascade Setup Procedure 22
- Cascade Autotuning Procedure 22
- . again 23
- Operations Page Map 26
- Autotune PID Cascade 27
- Autotune PID 27
- PID Set x (6 to 10) 28
- Autostart 34
- Ramp Time 34
- Ramp Rate 34
- Profile Plan Checklist 35
- How to Program a New Profile 36
- 6.Choose the end-state 37
- 7.Save your settings 37
- How to Edit a Profile 38
- User Profile Record 39
- Military Standard 810D 40
- Profiles Page Map 43
- Wait for: 45
- Event Output 46
- Analog Input x (1 to 3) 46
- Chapter Five: Setup 49
- Customizing the Main Page 50
- Input2 Cal. Offset 51
- Control Output x 52
- Scale Low: 0% 1-second Filter 53
- Setup Page Map 54
- Main > Setup > System 55
- Digital Input x (1 to 4) 58
- Retransmit Output x (1 and 2) 60
- Alarm Output x (1 and 2) 60
- Digital Output x (1 to 8) 61
- Communications 62
- Static Message 63
- Process Display 63
- Custom Main Page 63
- Setup Page Parameter Record 64
- Chapter Six: Features 65
- Inputs/Outputs 66
- Temperature 67
- Control Methods 68
- Dead Band 69
- Burst Fire 70
- Other Features 71
- Advanced Features 74
- Chapter Seven: Communications 77
- Series F4 Modbus Registers 78
- (expressed in percent) 79
- For more information 81
- Profile Parameters 86
- For more information about 91
- F4 Modbus Applications: 93
- (page 1 of 3) 96
- (page 2 of 3) 97
- Page Map 97
- (page 3 of 3) 98
- Jump Step End Step 99
- Renaming a Profile - F4 101
- Note: There are ten 101
- Modbus Registers for 101
- Overview 103
- Change a Password 104
- Set Lockout Menu Map 104
- Enter a Password 104
- Use a Password 104
- Set Lockout 105
- Chapter Nine: Calibration 107
- Calibrating the Series F4 108
- Process Output Procedure 110
- Retransmit Output Procedure 111
- Calibration Menu Map 112
- Calibrate Input x (1 to 3) 113
- Chapter Ten: Diagnostics 115
- Diagnostic 116
- Register 117
- Main > Factory > Test 118
- Chapter Eleven: Installation 119
- Panel Cutout 120
- Chapter Twelve: Wiring 123
- Power Wiring 124
- Thermocouple 125
- 0-20mA or 4-20mA Process 125
- 0 to 50mV 125
- Inputs x (2 and 3) 126
- Digital Inputs x (1 to 4) 128
- Outputs x (1A, 1B, 2A and 2B) 129
- Retransmit and Alarm Output 130
- Digital Outputs x (1 to 8) 131
- EIA/TIA-232 Connections 132
- EIA-232 or 133
- ICS Model 4899 133
- 59 60 61 62 134
- Appendix 135
- Glossary 136
- Series F4 139
- Specifications 140
- Ordering Information 141
- 5.10, 6.2 142
- List of Figures 147
- Series F4 Software Map 150
- Setup Page see Chapter 5 151
- Factory Page 151
- How to Reach Us 152
Related products and manuals for Sensors Watlow Series F4S/D
Sensors Watlow Series SD User Manual
(8 pages)
(8 pages)
Sensors Watlow Series F4S/D User Manual
(102 pages)
(102 pages)
Sensors Watlow Series SD Limit User Manual
(60 pages)
(60 pages)
Sensors Watlow Series PD User Manual
(188 pages)
(188 pages)
Sensors Watlow Series V4 User Manual
(21 pages)
(21 pages)
(80 pages)
Sensors Watlow Silver Series EM User Manual
(18 pages)
(18 pages)
Sensors Watlow Silver Series OIT User Manual
(14 pages)
(14 pages)
Sensors Watlow Series V4T User Manual
(26 pages)
(26 pages)
Sensors Watlow TLM-8 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 3.603 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals