Watlow CLS200, MLS300 and CAS200 User Manual Page 60
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
54 Communications Specification
Chapter 3: Controller Parameter Descriptions
(3) If the original precision value (from the table below) was a negative
number, round the number to the nearest integer. Otherwise, display
the number.
Exception
For the deviation band alarm, heat/cool spread, and alarm deadband
parameters, follow the procedure above, but if the precision value from
the table is negative, display the raw number read from the controller.
Display Format Menu
When users edit the controller’s Display Format menu for a linear input,
they are really editing the precision for that input.
The next table shows the available precision values:
Cycle Time (20)
This parameter contains the time proportioning time base, expressed in
seconds.
• Range: 0 to 255 seconds.
• Heat: 10.
• Cool: 3.
Zero Calibration (21)
This parameter returns the controller’s zero calibration counts.
Full Scale Calibration (22)
This parameter returns the controller’s full scale calibration counts
Digital Inputs (25)
This parameter returns the state of the controller’s digital inputs. If the
input is an open circuit (high) the corresponding value returns a 1. If the
input is connected to common or low a 0 is returned.
Precision
Value
Display Format
Sample Raw Value Read
via Communications
Scaled
Display Value
–1 –999 to 3000 2556 257
0 –9999 to 30000 2556 2556
1 –999.9 to 3000.0 2556 255.6
2 –99.99 to 300.00 2556 25.56
3 –9.999 to 30.000 2556 2.556
4 –0.9999 to +3.0000 2556 0.2556
- CLS200, MLS300 1
- Communications 1
- Specification 1
- Warranty 2
- Contents 3
- Protocol Syntax 9
- Transaction Sequence 10
- Packet Format 12
- Codes in a Packet 12
- Error Checking 14
- Cyclic Redundancy Check (CRC) 15
- Examples 16
- Block Write 19
- Message Data 20
- Data for a Write Command 21
- Two-Byte Data Types 21
- Figuring Block Size 21
- Anafaze/AB Data Table Summary 22
- Number Description 24
- Address 24
- Type Number of Bytes 24
- Overview 27
- The Query-Response Cycle 28
- Serial Transmission 28
- Message Framing 29
- Contents of the Data Field 30
- CRC Error Checking 31
- Function Codes 32
- Diagnostic Subfunctions 33
- Writing Data 36
- Reading Data 36
- Write Examples 38
- Modbus-RTU Data Table Summary 39
- Chapter 3: 45
- All Units 17, 18 47
- Enhanced Features options 49
- Parameters (by number) 51
- Input Type (3) 52
- Output Type (4) 53
- Setpoint (5) 54
- Process Variable (6) 54
- Output Filter (7) 54
- Output Value (8) 55
- Alarm Deadband (12) 55
- Alarm_Status (13) 56
- Ambient Sensor Readings (15) 58
- Pulse Sample Time (16) 58
- High Process Variable (17) 58
- Low Process Variable (18) 58
- Precision (19) 59
- Cycle Time (20) 60
- Zero Calibration (21) 60
- Full Scale Calibration (22) 60
- Digital Inputs (25) 60
- Digital Outputs (26) 61
- Override Digital Input (28) 61
- Override Polarity (29) 61
- System Status (30) 62
- System Command Register (31) 62
- Data Changed Register (32) 63
- Input Units (33) 63
- EPROM Version Code (34) 64
- Options Register (35) 64
- High Reading (37) 65
- Low Reading (38) 65
- Heat/Cool Spread (39) 65
- Startup Alarm Delay (40) 66
- • Range: See tables below 67
- • Default: 0 67
- Current Segment (47) 68
- Segment Time Remaining (48) 68
- Current Cycle Number (49) 68
- Tolerance Alarm Time (50) 68
- Last Segment (51) 68
- Number of Cycles (52) 69
- Ready Setpoint (53) 69
- Ready Event States (54) 69
- Segment Setpoint (55) 70
- Segment Time (58) 72
- Tolerance (59) 72
- Ramp/Soak Flags (60) 72
- Output Limit (61) 73
- Output Limit Time (62) 73
- Alarm_Control (63) 74
- Alarm_Acknowledge (64) 74
- Alarm_Mask (65) 74
- Alarm_Enable (66) 74
- AIM Fail Output (68) 75
- Output Linearity Curve (69) 76
- SDAC Mode (70) 76
- SDAC Low Value (71) 76
- SDAC High Value (72) 76
- Save Setup to Job (73) 77
- Input Filter (74) 77
- Loop Alarm Delay (75) 77
- Loop Names (77) 77
- Channel Name (78) 78
- Manufacturing Test (80) 78
- Cascade Maximum Setpoint (89) 80
- Cascade Base Setpoint (87) 80
- Cascade Minimum Setpoint (88) 80
- Loop Status (96) 82
- Output Type/Disable (97) 82
- Output Reverse/Direct (98) 82
- Controller Type (99) 83
- Ramp/Soak Profile Number (100) 83
- Controller Address (101) 83
- Baud Rate (102) 83
- Ready Events (103) 84
- Appendix A: 85
- Communications Driver 85
- Close_Comm_Port() 86
- DownLoad() 86
- UpLoad() 87
- Glossary 89
Related products and manuals for Sensors Watlow CLS200, MLS300 and CAS200
Sensors Watlow CLS User Manual
(180 pages)
(180 pages)
Sensors Watlow CLS200 User Manual
(251 pages)
(251 pages)
(2 pages)
(2 pages)
(2 pages)
Sensors Watlow CPC400 User Manual
(230 pages)
(230 pages)
© 2020, manymanuals.com. All rights reserved. | 0.637 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals