Watlow CLS200, MLS300 and CAS200 User Manual Page 25
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 1: ANAFAZE/AB Protocol
Communications Specification 19
54 Ready Event States 1180 UC MAX_RSP *
MAX_DIGOUT_BYTES
55 Segment Setpoint 1280 SI MAX_RSP * 2 *
MAX_SEG
56 Triggers and Trigger States 1780 UC MAX_RSP*
MAX_SEG*
MAX_TRIG
57 Segment Events and Event States 1C80 UC MAX_RSP * MAX_SEG
* MAX_EVENT
58 Segment Time 2680 UI MAX_RSP * 2 *
MAX_SEG
59 Tolerance 2B80 SI MAX_RSP * 2 *
MAX_SEG
60 Ramp/Soak Flags 3080 UC MAX_CH
61 Output Limit 3200 SI MAX_CH * 4
62 Output Limit Time 3280 SI MAX_CH * 4
63 Alarm_Control 3300 UI MAX_CH * 2
64 Alarm_Acknowledge 33C0 UI MAX_CH * 2
65 Alarm_Mask 3480 UI MAX_CH * 2
66 Alarm_Enable 3540 UI MAX_CH * 2
67 Output Override Percentage 3600 SI MAX_CH * 4
68 AIM Failure Output 3690 UC 1
69 Output Linearity Curve 3700 UC MAX_CH * 2
70 SDAC Mode 3740 UC MAX_CH * 2
71 SDAC Low Value 3780 SI MAX_CH * 4
72 SDAC High Value 3800 SI MAX_CH * 4
73 Save Setup to Job 3880 UC 1
74 Input Filter 3890 UC MAX_CH
75 Loop Alarm Delay 38D0 UI MAX_CH * 2
76 Not used 3990 16
77 Loop Names
(CLS/CLS200 and MLS/MLS300)
39A0 UI MAX_CH * 2
78 T/C Failure Detection Flags
(CLS/CLS200 and MLS/MLS300)
3A30 UC MAX_CH
78 Channel Name
(CAS/CAS200)
3994 UC MAX_CH * 8
79 Restore PID Digital Input 4130 UC MAX_CH
80 Manufacturing Test 4160 UI 1
81 PV Retransmit Primary Loop
Number
4200 UC MAX_CH * 2
82 PV Retransmit Maximum Input 4250 UI MAX_CH * 4
83 PV Retransmit Maximum Output 42E0 UC MAX_CH * 2
Number Description
Address
in Hex
Type Number of Bytes
- CLS200, MLS300 1
- Communications 1
- Specification 1
- Warranty 2
- Contents 3
- Protocol Syntax 9
- Transaction Sequence 10
- Packet Format 12
- Codes in a Packet 12
- Error Checking 14
- Cyclic Redundancy Check (CRC) 15
- Examples 16
- Block Write 19
- Message Data 20
- Data for a Write Command 21
- Two-Byte Data Types 21
- Figuring Block Size 21
- Anafaze/AB Data Table Summary 22
- Number Description 24
- Address 24
- Type Number of Bytes 24
- Overview 27
- The Query-Response Cycle 28
- Serial Transmission 28
- Message Framing 29
- Contents of the Data Field 30
- CRC Error Checking 31
- Function Codes 32
- Diagnostic Subfunctions 33
- Writing Data 36
- Reading Data 36
- Write Examples 38
- Modbus-RTU Data Table Summary 39
- Chapter 3: 45
- All Units 17, 18 47
- Enhanced Features options 49
- Parameters (by number) 51
- Input Type (3) 52
- Output Type (4) 53
- Setpoint (5) 54
- Process Variable (6) 54
- Output Filter (7) 54
- Output Value (8) 55
- Alarm Deadband (12) 55
- Alarm_Status (13) 56
- Ambient Sensor Readings (15) 58
- Pulse Sample Time (16) 58
- High Process Variable (17) 58
- Low Process Variable (18) 58
- Precision (19) 59
- Cycle Time (20) 60
- Zero Calibration (21) 60
- Full Scale Calibration (22) 60
- Digital Inputs (25) 60
- Digital Outputs (26) 61
- Override Digital Input (28) 61
- Override Polarity (29) 61
- System Status (30) 62
- System Command Register (31) 62
- Data Changed Register (32) 63
- Input Units (33) 63
- EPROM Version Code (34) 64
- Options Register (35) 64
- High Reading (37) 65
- Low Reading (38) 65
- Heat/Cool Spread (39) 65
- Startup Alarm Delay (40) 66
- • Range: See tables below 67
- • Default: 0 67
- Current Segment (47) 68
- Segment Time Remaining (48) 68
- Current Cycle Number (49) 68
- Tolerance Alarm Time (50) 68
- Last Segment (51) 68
- Number of Cycles (52) 69
- Ready Setpoint (53) 69
- Ready Event States (54) 69
- Segment Setpoint (55) 70
- Segment Time (58) 72
- Tolerance (59) 72
- Ramp/Soak Flags (60) 72
- Output Limit (61) 73
- Output Limit Time (62) 73
- Alarm_Control (63) 74
- Alarm_Acknowledge (64) 74
- Alarm_Mask (65) 74
- Alarm_Enable (66) 74
- AIM Fail Output (68) 75
- Output Linearity Curve (69) 76
- SDAC Mode (70) 76
- SDAC Low Value (71) 76
- SDAC High Value (72) 76
- Save Setup to Job (73) 77
- Input Filter (74) 77
- Loop Alarm Delay (75) 77
- Loop Names (77) 77
- Channel Name (78) 78
- Manufacturing Test (80) 78
- Cascade Maximum Setpoint (89) 80
- Cascade Base Setpoint (87) 80
- Cascade Minimum Setpoint (88) 80
- Loop Status (96) 82
- Output Type/Disable (97) 82
- Output Reverse/Direct (98) 82
- Controller Type (99) 83
- Ramp/Soak Profile Number (100) 83
- Controller Address (101) 83
- Baud Rate (102) 83
- Ready Events (103) 84
- Appendix A: 85
- Communications Driver 85
- Close_Comm_Port() 86
- DownLoad() 86
- UpLoad() 87
- Glossary 89
Related products and manuals for Sensors Watlow CLS200, MLS300 and CAS200
Sensors Watlow CLS User Manual
(180 pages)
(180 pages)
Sensors Watlow CLS200 User Manual
(251 pages)
(251 pages)
(2 pages)
(2 pages)
(2 pages)
Sensors Watlow CPC400 User Manual
(230 pages)
(230 pages)
© 2020, manymanuals.com. All rights reserved. | 0.304 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals